Cause analysis of poor toughness of TPE raw materials

TPE material not only simplifies the production process, but also reduces the production cost. Its products are environmentally friendly, beautiful and generous, which makes the products more artistic and creative. However, when producing and processing TPE materials, some customers sometimes encounter the problems of poor toughness and easy cracking. What is the reason? How to solve it? The first reason is that the temperature of TPE material is too high, which leads to material deterioration, physical properties degradation, brittleness and poor toughness. Solution: Be familiar with the suitable molding temperature of TPE materials after processing. In case of doubt, it is recommended to consult the material supplier. Second reason: TPE materials improve the filling ability, which leads to the decrease of tensile properties and flexibility. Solution: Reduce the proportion of filler added. Reason 3: When TPE materials are produced, the amount of waste recovery is too large. Solution: The toughness of nozzle material is poor, and too much dosage will usually reduce the toughness of TPE material. It is suggested that the nozzle adjustment and ratio should be less than 25%. The fourth reason is that the molding temperature of TPE material is not enough, the material is not completely plasticized, and the toughness is poor. Solution: Be familiar with the suitable molding temperature of TPE materials after processing. In case of doubt, it is recommended to consult the material supplier. When the surface smoothness of the commodity is low, if the surface smoothness is low, even if the surface appears, the molding temperature of the material must be increased; Second, look at the nozzle, if the nozzle surface lacks luster, the plasticizing temperature is very low. High quality TPE materials have good resilience and wear resistance. Temperature resistance, good hardness and good processability. TPE material particles can have good adhesion with some glues. Therefore, high-quality TPE particles can be obtained only if these properties are met. In view of the problem of poor toughness of TPE materials and the solutions, we will share with you here. TPE materials do not need vulcanization. It can produce rubber and plastic products, reduce vulcanization procedures, save investment, low energy consumption, simple processing technology, shorten production and processing cycle, improve productivity and reduce production and processing costs.

TPE material not only simplifies the production process, but also reduces the production cost. Its products are environmentally friendly, beautiful and generous, which makes the products more artistic and creative. However, when producing and processing TPE materials, some customers sometimes encounter the problems of poor toughness and easy cracking. What is the reason? How to solve it? The first reason is that the temperature of TPE material is too high, which leads to material deterioration, physical properties degradation, brittleness and poor toughness. Solution: Be familiar with the suitable molding temperature of TPE materials after processing. In case of doubt, it is recommended to consult the material supplier. Second reason: TPE materials improve the filling ability, which leads to the decrease of tensile properties and flexibility. Solution: Reduce the proportion of filler added. Reason 3: When TPE materials are produced, the amount of waste recovery is too large. Solution: The toughness of nozzle material is poor, and too much dosage will usually reduce the toughness of TPE material. It is suggested that the nozzle adjustment and ratio should be less than 25%. The fourth reason is that the molding temperature of TPE material is not enough, the material is not completely plasticized, and the toughness is poor. Solution: Be familiar with the suitable molding temperature of TPE materials after processing. In case of doubt, it is recommended to consult the material supplier. When the surface smoothness of the commodity is low, if the surface smoothness is low, even if the surface appears, the molding temperature of the material must be increased; Second, look at the nozzle, if the nozzle surface lacks luster, the plasticizing temperature is very low. High quality TPE materials have good resilience and wear resistance. Temperature resistance, good hardness and good processability. TPE material particles can have good adhesion with some glues. Therefore, high-quality TPE particles can be obtained only if these properties are met. In view of the problem of poor toughness of TPE materials and the solutions, we will share with you here. TPE materials do not need vulcanization. It can produce rubber and plastic products, reduce vulcanization procedures, save investment, low energy consumption, simple processing technology, shorten production and processing cycle, improve productivity and reduce production and processing costs.